MakeItMidi

← Back to the MP3 to MIDI converter

Can I make a karaoke MIDI file from an MP3?

Not as a finished karaoke track. A browser MP3-to-MIDI conversion gives you one melody line of note events with no lyric text, no accompaniment and no way to mute the original singer — so it is a starting point for building a karaoke file, not the karaoke file itself.

A full song on the left contains lead vocal, backing instruments and sung words. In the middle, a MIDI conversion writes only one track of note events and pitch bends, with no lyric events and no audio. On the right, a karaoke file needs those notes plus timed lyric text and a backing part, which have to be added separately.

What a karaoke file actually contains

A karaoke MIDI file — the kind often saved with a .kar extension — is a Standard MIDI File with one extra ingredient: timed lyric text. In SMF byte terms the words are stored as lyric meta events, status byte 0xFF followed by type 0x05, each carrying a short string of syllables and the tick position where it should light up. Everything else is ordinary MIDI: note events, durations, tempo, maybe a track name. The notes and the words are separate data living in the same file.

That distinction is exactly where an audio conversion stops. The MIDI reader bundled with this site can parse that event type (meta type 5 becomes a lyrics event) and its writer can serialize it back out as 0xFF 0x05 with a length and a string. But the conversion pipeline never emits one. It writes note-on and note-off events, plus continuous pitch-bend events, and that is the whole output: a Standard MIDI File (SMF) format 0, one track, 480 ticks per quarter note, written at 120 BPM. No lyric bytes are written, because there is no text anywhere in the input for the pipeline to write. Decode and pitch detection both run inside your browser, the audio never leaves your device, there is no upload, no account and no login, and you download the .mid directly. MP3, WAV, OGG, M4A/AAC and FLAC all decode to the same raw samples, and there is no file-length or file-size cap in the code beyond device memory.

Why a pitch detector cannot give you the words

Pitch detection reads short frames of a waveform and estimates one fundamental frequency per frame, then rounds that to a MIDI note number. Frequency in, note number out. There is no phoneme, no character, no language model and no lyric alignment anywhere in that chain. Recovering sung words from audio is a speech-recognition problem with a separate alignment step; a converter that only estimates pitch has nothing to write into a lyric event. This is a limit of what is being measured, not a missing setting or a premium tier.

There is a second, more ironic mismatch. Karaoke usually means removing the lead vocal and keeping the rest, with the words on screen. Converting a full song to MIDI does roughly the opposite: it extracts a single monophonic melodic line, not a chord-by-chord or instrument-by-instrument separation, and on a dense mix the most prominent moving pitch is often the singer. So the notes you get tend to be the very part a karaoke track takes out. And because MIDI carries no audio at all, the .mid cannot mute, fade or subtract a voice from your original recording — it is note data, not a processed copy of the song. If you need the singer gone from the audio, that is source separation, a different job.

Why a sung song is the hardest source

A full karaoke source is a voice over a complete arrangement, which is close to the worst case for a single-line pitch detector. During a pitch bend, slide, vibrato or ornament, the true fundamental frequency moves continuously between semitones. Each short analysis frame has to be quantized to the nearest note, so one sustained pitch becomes a little cluster of neighbouring semitones. Microtonal material gets pulled onto the nearest step of twelve-tone equal temperament for the same reason. This is worst on guitar bends and wide vibrato, vocal slides and melisma, string vibrato, blues and soul phrasing, and microtonal music; it is nearly absent on clean, isolated piano single notes and a steady synth lead. We publish no accuracy percentage, because the result depends entirely on the recording — any single number would be a guess.

Dense backing adds the classic phantom bass. A just-intoned major triad sits at the ratio 4 : 5 : 6: C4 (261.63 Hz), E4 (329.63 Hz) and G4 (392.00 Hz) are all close to integer multiples of 65.4 Hz (divide by 4, 5 and 6), so the combined waveform repeats roughly once every 1/65.4 s. A period-based detector locks onto that shared repetition and reports about 65.4 Hz — C2, two octaves below the lowest note actually played. It is the arithmetic of three real notes overlapping, not a bitrate problem and not a free-tier problem. In community threads the recurring complaint is that bends and slides make the output sound out of tune — not that the tool was free, and not that the source file was compressed. People describe the same drift on paid converters costing around $80. Choosing a tool by how it handles bends beats choosing it by whether it charges.

A workflow that actually works

  1. Convert the audio to a .mid first. Drop the file on the converter, press Convert to MIDI, then Download .mid. We do not claim any editor, karaoke app or notation program does or does not have a built-in lyric or karaoke mode — we have not verified that against an official source for every version, and guessing about someone else's feature list would be worse than giving you a route that works everywhere. The step that always holds is: get the notes in first, then add the rest in your editor.
  2. Set the tempo before aligning anything. The file is written at a fixed 120 BPM and carries no tempo map from the original song, so set your project to the real speed before placing syllables against the notes.
  3. Add the lyric text and a backing part yourself. Timed words and an accompaniment are content you supply; pitch detection cannot produce either. Keep your original recording for the audio you actually want to hear.
  4. Treat a bend-heavy take as a draft. Read the spectrogram for where notes glide or carry grace notes and correct those positions by hand, use a single-note or monophonic mode if your editor has one, and pick the cleanest source you can — a solo take over a full mix. Cleaning the source beats cleaning the output.

Convert an audio file to MIDI

Related questions